The installation of window frames is a key stage of construction and modernization, which significantly affects the thermal comfort, acoustic comfort and energy efficiency of the building. However, the correct installation of windows is not everything – it is equally important to work properly with polyurethane foam to ensure effective sealing.
In this article, we will focus on the most common mistakes associated with working with PU foam during the installation of window frames, and suggest how to avoid them.
- Mistake No. 1: Skipping the water wetting step when applying polyurethane foam
- Mistake No. 2: Filling the gap between the frame and jamb incorrectly
- Mistake No. 3: Failure to protect the cured foam from the weather
- Mistake No. 4: Improper mixing of foam before application
- Mistake No. 5: Using the wrong foam depending on seasonal conditions
- Mistake No. 6: Improper storage of foam
- Mistake No. 7: Mistakes in the use of one- and two-component foams
Mistake No. 1: Skipping the Water Wetting Step When Applying Polyurethane Foam
One of the most common mistakes when working with single-component polyurethane foam is skipping the stage of wetting the surface with water before and after foam application. This step is crucial because proper moisture content of the substrate affects the proper curing of the foam, and thus its insulation properties and adhesion to the surface. Lack of wetting can lead to an inhomogeneous foam structure, the formation of voids and a reduction in insulation effectiveness.
How to remedy this?
Always spray the surface with water before and after the application of single-component polyurethane foam, especially at temperatures above 0°C, to ensure proper conditions for the foam to cure. Use a sprayer that provides an even spray of water to make your job easier. For a detailed discussion of wetting technique and its importance, see the dedicated article.
Mistake No. 2: Filling the Gap Between the Frame and Jamb Incorrectly
A common mistake is inaccurately filling the gap between, for example, the window frame and the jamb. Irregular filling or leaving spaces unfilled can lead to thermal bridges, resulting in increased heat loss and worsening thermal comfort in the room. In addition, such gaps can allow moisture to pass through, leading to mold growth and damage to structural materials.
How to remedy this?
When applying foam, make sure you fill the entire gap evenly. For deep gaps, apply the foam in layers, wetting each layer before applying the next. For typical window profiles with a depth of about 8 cm, it is recommended to apply in two stages, and for deeper gaps, such as for HS sliding doors with a depth of 19 cm, divide the application into even more stages.
Mistake No. 3: Failure to Protect the Cured Foam From the Weather
Polyurethane foam, once cured, is sensitive to UV light, moisture and varying temperatures. Unprotected foam begins to degrade, lose its insulating properties, and in extreme cases can disintegrate completely. Exposure to the sun causes the foam to change color, and it crumbles and settles, leading to deterioration of the seal.
How to remedy this?
As soon as possible after the foam is fully cured, protect it with appropriate sealing tapes or protective coatings that will provide resistance to UV radiation and other atmospheric factors. It is worth using liquid films that protect, seal and further help control the flow of moisture in the joint. Do not leave foam exposed to the elements without proper protection to avoid degradation and costly repairs.
Mistake No. 4: Improper Mixing of Foam Before Application
Another common mistake is improper mixing of the foam before application. Polyurethane foam is composed of many chemical components, the selection of which is carefully considered by our experts in R&D. During the production process, the right polymers, propellants and other additives are selected, which is key to achieving the right foam properties. The ingredients in the can can separate during storage.
How can this be remedied?
Shake the can thoroughly before use – about 30 vigorous shakes with the valve facing down are recommended to thoroughly mix all the ingredients and ensure that the foam cures evenly after application.
Mistake No. 5: Using the Wrong Foam Depending on Seasonal Conditions
Polyurethane foams are available in summer, winter and multi-season versions that are designed to work at specific temperatures. Using summer foam in winter conditions can lead to curing problems and improper adhesion of the foam to the surface. Summer foams have a minimum application temperature of +5°C, multi-season foams can be used down to -10°C, and winter foams can be used as low as -20°C.
How to remedy this?
Choose the right foam for the site conditions. In colder weather, reach for winter or multi-season foams, which are adapted to lower temperatures and can cure even at low temperatures. In temperate and summer conditions, use summer or multi-season foams.
Mistake No. 6: Improper Storage of Foam
Polyurethane foam should be stored at a temperature according to the manufacturer’s recommendations. Keeping the can too cold (such as storing it outside in winter) or too hot (such as leaving the can in a heated car in summer) can affect its properties and even your safety.
How to remedy this?
Store the foam in places with stable temperatures, avoiding extreme conditions. Cans should be stored upright, with the valve up. The foam should be at the right temperature before application – for example, a can of Tytan Professional 65 foam requires a storage temperature of at least +5°C and mx 35°C, even though the temperature outside may be much lower.
Mistake No. 7: Mistakes in the Use of One- And Two-Component Foams
Polyurethane foams are available in one- and two-component versions, which have different uses and application requirements. One-component foams are the most popular and make up the majority on the market, mainly because of their ease of use and performance. Two-component foams, while less popular, offer higher density, greater mechanical strength and and the curing process is independent of ambient moisture, thanks to the hardener inside the can. However, improper preparation of two-component foam, such as omitting to mix the ingredients by turning the mechanism several times, leads to improper curing and reduced insulation performance.
How to remedy this?
When using two-component foams, make sure you carefully release the hardener and mix the product components. Use two-component foam where access to moisture is limited, such as in closed chambers or under floors. In areas where moisture is present, choose a one-component foam and be sure to moisten it with water.
Thoroughly filling gaps, using the right foam for the conditions and properly protecting it from the elements will ensure durable and effective seals. By taking care of these details, you show professionalism and avoid mistakes that can reduce the quality of the work done.