855-448-9826

TYTAN Foam Bond 60 Foam Adhesive (24 oz. Gun)


 

$26.00

00971
In stock
Also available in cases of 12. 10% discount automatically applied when the number of purchased items is a multiple of the case number.

TYTAN Foam Bond 60 Foam Adhesive

TYTAN Foam Bond 60 PRO Foam Adhesive’s innovative formula bonds architectural foam shapes and foam panels fast! It does not contain solvents so it does not have an offensive odor and is safe for all foams. It bonds after 60 seconds and is secure after 5 minutes. It performs well on damp surfaces and has excellent bond strength on a range of popular construction materials. The TYTAN PRO applicator reduces body strain and allows you to work faster compared to using a conventional cartridge applicator. It cures by the moisture in the air, so high humidity speeds up the curing process. 

  • Industries:
    • Architectural Foam
    • EIFS
    • SIPs
    • Residential Insulation
  • Materials:
    • XPS Board
    • EPS Board
    • Polyiso board
    • Foam to Foam
  • Applications:
    • Foundation Foam Board
    • Exterior Sheathing Foam Board
    • Block Wall Foam Board
    • Wood or Steel Stud Wall Foam Board
    • Attic Cavities
    • Wall Cavity

How to Use:
1. Wearing work clothes, gloves, and eye protection is recommended. 2. Use only with adequate ventilation or approved respiratory equipment. 3. Clean the surface of oil, dust and greases. For best results, and maximum yield, apply at temperatures 41°F-95°F. Use below 32°F is not recommended. Protect valuables around the area being sprayed with tape, cloth, plastic, or other material. If being used on a vertical surface, be sure to protect beneath the application area. 4. Shake can vigorously for 30-45 seconds. Remove protective cap, invert can, and screw the can firmly onto the TYTAN dispensing gun – do not over tighten. Maintain the can in upside-down, inverted position during application of the foam. Slowly dispense material in a trash bin to test dispensing flow rate. Adjust control knob on gun handle to achieve the desired application flow. 5. Slowly apply the foam adhesive to desired location. A serpentine bead should be used when possible. 6. Wait 60 seconds before applying the substrate. Higher humidity will speed up the curing process. Pulling the substrate away and then reapplying a few seconds later will speed up the bond time. Material must be attached within 2 minutes for desired performance. 7. Press and hold until the substrate is set. Secure with mechanical fasteners when appropriate. Substrate will adhere within 3-5 minutes. Full cure after 48 hours. For more information, go to the “Try TYTAN” tab at TYTAN.com 

Gun Cleaning: Only use TYTAN Universal Cleaner in well-ventilated areas or with approved respiratory equipment. Use TYTAN Universal Cleaner’s spray nozzle to sprayany uncured foam off the end of the gun applicator nozzle into a trash can ora throw away material. Remove the used foam canister from the gun applicator and spray all external uncured foam with TYTAN Universal Cleaner. Screw the TYTAN Universal Cleaner canister onto the gun and spray the cleaner through the gun to clean uncured foam out the inside of the gun barrel. Leave the TYTAN Universal Cleaner canister screwed onto the gun applicator. Tighten the control knob on the guns handle so no air can enter the barrel of the gun. Air entering the barrel of the gun for more than 2-3 minutes will decrease the efficiency and life of your gun. TYTAN Wipes may be used to clean the tip of the applicator. Regularly cleaning the tip will increase the life and efficiency of the applicator. 

Foam Clean up: Spray any uncured foam with TYTAN Universal Cleaner and wipe away with a disposable material. You may also use nail polish remover, acetone, or paint thinner for easy clean-up of uncured foam. Cured foam cannot be removed with solvents. Cured foam must be removed mechanically and may leave a residue. Cured foam can be removed from skin using an industrial cleaner with pumice or petroleum jelly. Cured foam will wear away over time and is not harmful to health.

Technical Specifications:
Can Temperature: 41°F-95°F
Ambient Temperature: 32°F-95°F
Fully Cured: 24 Hours
Shelf Life: 12 Months

Downloads:
  • Gun
  • Indoors
  • Outdoors
  • Foam Adhesive
Visit us on Twitter Visit us on Facebook Visit us on YouTube Visit us on Vimeo Visit us on Google

Track my order(s)

 

TYTAN Eco Gun (Black)

  $21.00
   

TYTAN 22" PRO (Black)

  $80.00
 
 

TYTAN Pro Control Gun (Blue)

  $37.00
   

TYTAN Foam Bond 60 Foam Adhesive (24 oz. Gun)

  $26.00